Short curing time bulk fill composite systems: volumetric shrinkage, degree of conversion and Vickers hardness.

This study aimed to evaluate volumetric polymerization shrinkage, degree of conversion and Vickers hardness of four bulk-fill resin composites light-activated with their dedicated light curing units (LCUs). Four groups were evaluated, according to the type of composite and curing mode: Tetric EvoCeram Bulk-fill (TEBO) and Tetric EvoFlow Bulk-fill (TEBF) were light-activated with Bluephase Style 20i (20s, in high-mode), while Tetric Powerfill (TEPO) and Tetric Powerflow (TEPF) were light-activated with Bluephase PowerCure (3s). Volumetric polymerization shrinkage test (n = 6) was performed in standardized box-shaped class-I cavities of extracted third molars (4 x 4 x 4 mm). Teeth were scanned before and after resin composite application by micro-computed tomography, and acquired data were evaluated with Amira software. Degree of conversion (n = 5) was evaluated at the top and bottom surfaces of composite cylindric samples (4 mm diameter, 4 mm thickness) using an FT-IR spectrometer (spectra between 1,500 and 1,800 cm-1, 40 scans at a resolution of 4 cm-1). Three Vickers indentations (50 g / 15 s), spaced 500 µm apart, were performed on the top and bottom composite surfaces and averaged. One-way ANOVA was used for data evaluation. TEPF showed the lowest volumetric polymerization shrinkage (p < 0.05), while the other composites were not significantly different within each other (p > 0.05). All materials presented a significant decrease in degree of conversion and Vickers hardness when compared top to bottom surfaces (p < 0.05). Bottom to top surface ratios for degree of conversion ranged from 0.8 (TEBO and TEPO) to 0.9 (TEBF and TEPF), and from 0.4 (TEPO) to 0.7 (TEBF and TEPF) for hardness. In conclusion, resinous materials present a decrease in hardness and degree of conversion from top to bottom even when a higher power is used, while the flowable material TEPF showed the lowest volumetric shrinkage values compared to the other materials.

Transitioning from injectable resin composite restorations to resin composite CAD/CAM veneers: A clinical report.

OBJECTIVE: To describe a shift from injectable resin composite technique to composite resin computer-aided design and computer-aided manufacturing (CAD/CAM) veneers in addressing esthetic concerns associated with diastemas between anterior lower teeth in a clinical case. CLINICAL CONSIDERATIONS: Among several techniques proposed for direct resin composite restoration, the "Injectable resin composite technique" has gained popularity for its time-efficiency, reduced technique sensitivity, and diminished reliance on clinician skills. However, challenges such as staining and the need for frequent polishing follow-ups may prompt the consideration of more stable alternatives such as indirect veneer restorations. While ceramic veneers offer superior mechanical and optical properties, resin ceramic veneers, especially those milled from CAD/CAM resin ceramic blocks, offer advantages such as rapid, cost-effective production, simplified intra-oral repairs, less susceptibility to fracture, superior stress absorption, and requires minimal tooth preparation, making them an appealing option for many patients. Moreover, a fully-digital approach not only streamlines the process but also saves time and labor while ensuring the delivery of high-quality restorations to patients. CONCLUSION: In addressing a patient's dissatisfaction with constant polishing of direct resin composite restorations, a shift to resin composite CAD/CAM veneers was implemented. Utilizing a fully-digital approach with CAD/CAM resin ceramic restorations successfully restored both esthetics and function. CLINICAL SIGNIFICANCE: While the injectable resin composite technique achieves immediate esthetic results, its low color stability necessitates frequent polishing sessions. The replacement of direct resin composite restorations with CAD/CAM resin composite veneers becomes a viable option for patients seeking more stable restorations that require fewer follow-ups. This transition addresses both esthetic concerns and the need for enduring solutions in restorative dentistry.

Analysis of translucency parameter and fluorescence intensity of 5 resin composite systems.

The natural outcome of dental composite restorations highly depends on the translucency of the enamel layer and fluorescence. This study aimed to evaluate the Translucency Parameter (TP) and Fluorescence Intensity (FI) of five different resin composite systems. Seven discs of each composite brand were prepared in a circular increasing thickness. For TP, a spectrophotometer measured the samples' colors. The color difference within the white/black backgrounds obtained the translucency parameter. For FI, samples were exposed to UV light, and ten photographs per group were taken. Each specimen was analyzed digitally. A mixed model analysis to a 95% confidence level analyzed groups differences. Higher values of TP were observed for ED and EL, followed by FZ. The lowest values were observed for EO and FO. FI values descending order was EL>FO>EO>ED>FZ. The composition of fillers and organic matrix influenced the behavior of fluorescence and translucency of resin composites. Key words:Resin composite, fluorescence, color, translucency parameter.

A fully digital low-cost workflow of a multidisciplinary minimally invasive treatment: step-by-step from function to esthetics.

This clinical case outlines a comprehensive digital workflow for a minimally invasive multidisciplinary treatment. The process utilizes one open-source software for digital wax-up and one low-cost software to address esthetic concerns related to teeth misalignment. The patient's function was stabilized with a digitally made occlusal splint. The application of the described digital workflow technique, incorporating open-source, low-cost, and closed software, played a pivotal role in attaining a straightforward and predictable outcome with minimally invasive treatment. Furthermore, the continual evolution of technology contributes to the growing precision of dental procedures. The presented digital workflow helped formulate a predictable treatment plan, replicate a diagnostic digital wax-up, and achieve precise teeth alignment. This approach satisfactorily addressed the patient's esthetic concerns, providing an outstanding approximation of the definitive result.

Ultrathin lithium disilicate and translucent zirconia crowns for posterior teeth: Survival and failure modes.

PURPOSE: To evaluate the reliability and failure modes of ultrathin (0.5 mm) lithium disilicate, translucent and ultra-translucent zirconia crowns for posterior teeth restorations. MATERIALS AND METHODS: Fifty-four mandibular first molar crowns of three ceramic materials: (1) Lithium disilicate (e.max CAD, Ivoclar Vivadent), (2) 3Y-TZP (Zirconn Translucent, Vipi), and (3) 5Y-PSZ (Cercon XT, Dentsply Sirona), with 0.5 mm of thickness were milled and cemented onto composite resin abutments. Eighteen samples of each group were tested under mouth-motion step-stress accelerated life testing in a humid environment using mild, moderate, and aggressive profiles. Data was subjected to Weibull statistics. Use level curves were plotted and reliability was calculated for a given mission of 100,000 cycles at 100, 200, and 300 N. Fractographic analyses of representative samples were performed in scanning electron microscope. RESULTS: Beta (ß) values suggest that failures were dictated by material's strength for lithium disilicate and by fatigue damage accumulation for both zirconias. No significant differences were detected in Weibull modulus and characteristic strength among groups. At a given mission of 100,000 cycles at 100 N, lithium disilicate presented higher reliability (98% CB: 95-99) regarding 3Y-TZP and 5Y-PSZ groups (84% CB: 65%-93% and 79% CB: 37&-94%, respectively). At 200 N, lithium disilicate reliability (82% CB: 66%-91%) was higher than 5Y-PSZ (20% CB: 4%-44%) and not significantly different from 3Y-TZP (54% CB: 32%-72%). Furthermore, at 300 N no significant differences in reliability were detected among groups, with a notable reduction in the reliability of all materials. Fractographic analyses showed that crack initiated at the interface between the composite core and the ceramic crowns due to tensile stress generated at the intaglio surface. CONCLUSIONS: Ultrathin lithium disilicate crowns demonstrated higher reliability relative to zirconia crowns at functional loads. Lithium disilicate and zirconia crown's reliability decreased significantly for missions at higher loads and similar failure modes were observed regardless of crown material. The indication of 0.5 mm thickness crowns in high-load bearing regions must be carefully evaluated. CLINICAL SIGNIFICANCE: Ultraconservative lithium disilicate and zirconia crowns of 0.5 mm thickness may be indicated in anterior restorations and pre-molars. Their clinical indication in high-load requirement regions must be carefully evaluated.

Quo vadis, esthetic dentistry? Part II: Composite resin overtreatment and social media appeal.

OBJECTIVES: This article presents case reports highlighting over-treatments with resin composites, often misconceived as minimally invasive procedures. CLINICAL CONSIDERATIONS: Tooth-colored restorative materials, such as ceramics and composites, have found widespread application to correct problems related to tooth color, shape, and alignment. When composite resin is used, these procedures can be done in a very conservative, cost-effective, and timely fashion. However, it is noteworthy that contemporary dental esthetic expectations are based on standards propagated by social media and other marketing and communications platforms. The abuse of and addiction to social media impacts can lead to unrealistic esthetic expectations and standards for both patients and dentists. CONCLUSIONS: After a critical discussion on ceramic veneers published in part I of this 2-part series, this article directs attention towards what has become a trendy fashion, i.e., the use of direct composite resins as "non-prep" veneers in clinical situations that arguably required no restorative intervention at all. We further explore how social media influences the decision-making processes of both professionals and patients.

Total Rehabilitation Using Adhesive Dental Restorations in Patients with Severe Tooth Wear: A 5-Year Retrospective Case Series Study.

INTRODUCTION: Currently, there is little clinical evidence to support the medium- and long-term survival and clinical performance of ultraconservative approaches using adhesive restorations in full-mouth restorations. The aim of this case series study was to evaluate the medium-term clinical performance of anterior and posterior adhesive restorations applied with direct and indirect techniques using resin composites and glass-ceramic-based materials. MATERIALS AND METHODS: The inclusion criteria were an esthetic problem as the main reason for consultation and severe generalized wear of grade 2 to 4 according to the Tooth Wear Evaluation System (TWES 2.0). In addition, at each follow-up appointment, patients were required to submit a clinical-parameter-monitoring record according to the modified United States Public Health Service (USPHS) criteria. RESULTS: Eight patients with severe tooth wear were treated through full rehabilitation in a private dental clinic in Spain by a single operator (AFC). A total of 212 restorations were performed, which were distributed as follows: 66 occlusal veneers, 26 palatal veneers and 120 vestibular veneers. No signs of marginal microleakage or postoperative sensitivity were observed in any occlusal, vestibular and/or palatal restoration after the follow-up period. The estimated survival rate of the 212 restorations was 90.1% over 60 months of observation, with a survival time of 57.6 months. Only 21 restorations had complications, which were mostly resolved with a direct composite resin. The dichotomous variables of the restoration type (posterior veneer, anterior veneer) and the type of restored tooth (anterior, posterior) were the risk predictors with statistically significant influences (p < 0.005) on the survival of the restorations. CONCLUSION: According to the results of this study, there is a significantly higher risk of restorative complications in posterior teeth compared to anterior teeth. Also, it can be concluded that the indication of adhesive anterior and posterior restorations is justified in the total oral rehabilitation of patients with severe multifactorial tooth wear, as they are associated with a low risk of failure.

Manufacturing and characterization of a 3D printed lithium disilicate ceramic via robocasting: A pilot study.

OBJECTIVE: The objective of this study was to manufacture and to evaluate the physico-mechanical properties of the Lithium disilicate (Li2O5Si2) ceramic structures fabricated using additive manufacturing (3D printing). METHODS: Li2O5Si2 samples were divided into (n = 30/group): SM (subtractively manufactured) and AR (additive/robocasting). For the AR group, Li2O5Si2 powder was combined with ammonium polyacrylate, hydroxypropyl methylcellulose, and polyelectrolyte to create a colloidal gel, which was then used for printing. A digital CAD model of a disc was designed, and the G-code transferred to a custom built DIW 3D printer. The control group samples were prepared using pre-crystallized ceramic blocks, which were cut to obtain discs with same dimensions as the AR group. Disc-shaped specimens from both groups were crystallized at 840 °C. Mechanical properties were evaluated using biaxial flexural strength test (BFS) and Vickers hardness test. Representative fractographic images of the specimens were acquired using scanning electron microscopy (SEM) to analyze the fracture origin and crack propagation. Energy-dispersive X-ray spectroscopy (EDS) and attenuated total reflection Fourier transform infrared spectroscopy (FTIR-ATR) were used for chemical analysis, and X-ray diffractometry (XRD) was performed to analyze the crystalline phases. RESULTS: AR group yielded lower values of BFS (120.02 MPa ±33.91) and hardness (4.07 GPa ±0.30), relative to the SM group, (325.09 MPa ±63.98) and (5.63 GPa ±0.14), respectively. For EDS analysis, AR and SM groups showed similar elemental composition. In FTIR-ATR analysis, higher peaks referring to the crystalline structure were found for SM group. XRD analysis indicated a decreased formation of Li2O5Si2 from Lithium metasilicate (Li2O-SiO2) in the AM group. SEM micrographs showed a more porous microstructure associated with the 3D printed samples. SIGNIFICANCE: The viability of fabricating Li2O5Si2 ceramic constructs using the Robocasting technique was successful. However, the samples prepared using subtractive manufacturing presented higher mechanical properties compared to the 3D printed constructs. The difference in properties between the manufacturing may be correlated to the decreased formation of Li2O5Si2 crystals and higher degrees of porosity.

Effect of different tightening protocols on the probability of survival of screw-retained implant-supported crowns.

PURPOSE: This study evaluated the effect of different tightening protocols on the probability of survival of screw-retained implant-supported anterior crowns. MATERIALS AND METHODS: Seventy-two implants with internal conical connections (4.0 × 10mm, Ti-6Al-4V, Colosso, Emfils) were divided into four groups (n = 18 each): 1) Manufacturer's recommendations torque (25 N.cm for abutment's screw and 30 N.cm for crown's screw) (MaT); 2) Retightening after 10 min (ReT); 3) Torque 16% below recommended to simulate an uncalibrated wrench (AgT), and; 4) Temporary crown simulation (TeT), where crowns were torqued to 13 N.cm to simulate manual tightening, subjected to 11,200 cycles to simulate temporary crown treatment time (190 N), and then retightened to manufacturer torque (TeT). All specimens were subjected to cyclic fatigue in distilled water with a load of 190 N until 250,000 cycles or failure. The probability of survival (reliability) to complete a mission of 50,000 cycles was calculated and plotted using the Weibull 2-Parameter analysis. Weibull modulus and number of cycles at which 62.3% of the specimens would fail were also calculated and plotted. The failure mode was characterized in stereo and scanning electron microscopes (SEM). RESULTS: The probability of survival was 69.3% for MaT, 70% for ReT, 54.8% for AgT, and 40.3% for TeT, all with no statistically significant difference. Weibull modulus was approximately 1.0 for all groups. The characteristic number of cycles for failure was 105,000 cycles for MaT, 123,000 for ReT, 82,000 cycles for AgT, and 54,900 cycles for TeT, with no significant difference between groups. The chief failure mode for MaT, ReT, AgT groups was crown screw fracture, whereas abutment screw fracture was the chief failure mode for the TeT group. CONCLUSION: Tightening protocol did not influence the probability of survival of the screw-retained anterior crowns supported by internal conical implants (Ti-6Al-4V, Colosso, Emfils).

Opalescence and color stability of composite resins: an in vitro longitudinal study.

OBJECTIVES: This study aims to evaluate the opalescence (OP) and color stability of composite resins over a period of 180 days and to compare composite resins' OP with enamel's OP. MATERIALS AND METHODS: Twenty human enamel specimens (5.0 × 0.3 mm) and 9 specimens (10.0 × 1.0 mm) of 10 colors of 4 different composite resins (3 M ESPE, FGM, Ivoclar-Vivadent, Miscerium) and one brand of adhesive (3 M ESPE) were made. The results were obtained by measuring the reflectance and transmittance spectra in the visible region. After baseline measurement, composites and adhesive were analyzed after 2, 7, 30, 60, 120, and 180 days. The Lab color coordinates were used in the calculations of the OP parameter and color differences in the CIELab and CIEDE2000 methods. The data were analyzed statistically. RESULTS: The materials tested showed variation and an increase in OP over time. The OP found for enamel was 18.06 ± 2.99, and some resins showed higher results. There was a strong correlation between the coordinate b*T and the OP over time. Enamel Plus was the only one material that presented no color changes during all periods in both color analyses. Filtek Z350 XT, AT, and BT did not show differences in any time when analyzed by CIELAB. CONCLUSIONS: The OP of most composite resins changed during the period of 180 days and was different from the OP of tooth enamel. In general, composites demonstrated small color changes over the period tested, being this characteristic material dependent. CLINICAL RELEVANCE: Natural teeth present different optical properties. Composite resins restorations should present properties similar to natural teeth and it is important that characteristics like color and opalescence remain stable over time.

Comparison of the operative time and presence of voids of incremental and bulk-filling techniques on Class II composite restorations.

OBJECTIVES: To compare the operative time and presence of air voids on Class II restorations fabricated by dental practitioners with 1 to 5 years of experience using incremental and bulk-filling techniques. METHOD AND MATERIALS: Four techniques were evaluated: incremental, bulk-filling, bulk-filling with heated composite, and snowplow technique. Standardized mandibular first molars with a MOD (mesial, occlusal, and distal) cavity were used. Voluntary operators made two restorations using each technique and the time required for each restoration was recorded. The restorations were scanned by micro-computed tomography to calculate the volume of the restoration occupied by air voids. The "operative time" and "volume of air voids" were analyzed individually by two-way ANOVA and Tukey HSD post hoc (α = .05) for the factors operator and insertion technique. A correlation between "operative time" and "volume of air voids" was evaluated using Pearson coefficient (α = .05). RESULTS: The incremental technique required significantly longer time, yet no differences were observed between the bulk-filling techniques. There were no significant differences between techniques regarding the volume of air voids. A significant, but weak, and inverse linear correlation (P = .0059; r = -.29; r2 = 8.41%) was found between the operative time and volume of air voids. CONCLUSION: There were no significant differences in the volume of air voids among the evaluated techniques, although bulk-filling techniques required a shorter operative time. Hence, implementing bulk-filling techniques by dental schools and restorative dental practitioners with different levels of expertise may reduce chair time and produce a volume of air voids similar to the incremental technique.

Quo vadis, esthetic dentistry? Ceramic veneers and overtreatment-A cautionary tale.

The increased emphasis on orofacial esthetics, experienced both by dental professionals and the lay public, results in an environment where overtreatment can easily occur. Patients on the one hand feel pressure from esthetic norms that are often unrealistic, while dental professionals are compelled to deliver immediate results many times without considering what is best for the ill-informed patient. This article is an illustrated cautionary tale against overtreatment disguised as esthetic dentistry. Representative clinical examples illustrate how porcelain veneers are used without following sound operatory principles, as well as how these cases have been resolved.

A comparison of ceramic crown color difference between different shade selection methods: Visual, digital camera, and smartphone.

STATEMENT OF PROBLEM: The light source stability of digital cameras and smartphones is important in shade matching in restorative and prosthetic dentistry to communicate objectively with the dental laboratory. Techniques that standardize the light source of such devices are lacking, and this limitation can lead to color mismatches, difficulties in color communication, and treatment documentation. PURPOSE: The purpose of this clinical study was to compare the magnitude of color difference (ΔE) among 3 shade selection methods during the fabrication of ceramic crowns: visual shade selection with a shade guide, digital shade selection with a digital camera and cross-polarizing filter, and digital shade selection with a smartphone and a light-correcting device. MATERIAL AND METHODS: Forty-five patients in need of ceramic crowns were enrolled, and shade selection was evaluated according to different protocols: visual shade selection (A-D shade guide and IPS Natural Die Material Shade Guide, sent to the dental laboratory technician via a laboratory prescription); digital shade selection with a digital camera (D7000; Nikon Corp) with an 85-mm lens and wireless close-up flash, with and without a cross-polarizing filter (Polar eyes); and digital shade selection with a smartphone and a light-correcting device (iPhone XS attached to Smile Lite MDP, with and without its cross-polarizing filter accessory). Information from the smartphone was imported to an app (IPS e.max Shade Navigation App; Ivoclar AG) that converted the reading to a shade and level of translucency for the ceramic restoration. For all photographs, a gray reference card with known color values was positioned by the mandibular teeth and was used for white balancing of the digital photographs with a software program. All photographs were edited and sent to the dental laboratory: white-balanced with the shade guide; white-balanced with the substrate shade guide; black and white; saturated; and cross-polarized. Ceramic crowns were made with the same lithium disilicate material (IPS e.max CAD; Ivoclar AG) and cemented with the same resin cement (RelyX Ultimate Clicker, A3 shade; 3M). The ΔE values between the crown and the adjacent tooth were determined. The data were analyzed by using a 1-way analysis of variance (ANOVA) and Tukey post hoc tests (α=.05). RESULTS: The mean ΔE between a cemented ceramic crown and the adjacent tooth in the visual shade selection group was 5.32, significantly different than both digital camera (ΔE=2.75; P=.002) and smartphone (ΔE=2.34; P=.001), which were not different from each other (P=.857). CONCLUSIONS: The digital shade selection with photographs acquired with both a digital camera and a smartphone with a light-correcting device showed a threshold within the acceptable values (ΔE<3.7), whereas the visual shade selection showed an average ΔE above the threshold for acceptable values (ΔE>3.7). The use of a gray reference card helped standardize the white balance from the digital images.

Evaluation of trueness and precision of two intraoral scanners and a conventional impression: an in vivo clinical study.

OBJECTIVE: To evaluate, in vivo, trueness and precision of two intraoral scanners, CEREC Omnicam (OMNI) and CEREC Primescan (PRIM), compared to a conventional impression serving as a master model. METHOD AND MATERIALS: Impressions were performed for seven participants. For each participant, conventional polyvinylsiloxane impression and digital impressions using two intraoral scanners, OMNI (software 4.6; CEREC ORTHO Protocol) and PRIM (10 digital impressions per participant, per scanner), were made. Conventional impression was digitized with a laboratory scanner (INEOS X5), and used as reference model. .STL files were superimposed with software (Geomagic Control X) using the tools Initial Alignment and Best Fit Alignment, and trueness and precision were evaluated. Statistical evaluation was performed with Shapiro-Wilk and Mann-Whitney tests (P < .05). RESULTS: Total mean trueness for the OMNI system was 56.45 ± 7.80 µm, and 47.29 ± 5.47 µm for the PRIM system. Regarding precision, values from the OMNI system were 42.47 ± 6.91 µm and from the PRIM system 21.86 ± 4.40 µm. PRIM presented better results for both trueness (P = .000) and precision (P = .000) when compared to OMNI. CONCLUSIONS: PRIM provided a better combination of trueness and precision than its predecessor OMNI. However, both PRIM and OMNI performed acceptably when performing indirect restorations, according to the current acceptable thresholds, considering both trueness and precision. CLINICAL IMPLICATIONS: Full-arch impressions with Primescan presented more precision and trueness than Omnicam; however, compared to previous reported values of conventional impressions, they still presented lower accuracy.

Effect of argon plasma on repair bond strength using nanofilled and microhybrid composites.

OBJECTIVES: To evaluate the effect of atmospheric pressure plasma (PLA), sandblasting (SAN), silanization (SIL) and hydrophobic bonding resin (HBR) on the micro-shear bond strength (MSBS) of fresh nanofilled (NF) or microhybrid (MH) composites to water-aged nanofilled composite. MATERIALS AND METHODS: NF plates were fabricated and stored in distilled water for 4 months. The aged plates were assigned to the groups (n = 6): 1- untreated; 2- SAN + SIL + HBR; 3- HBR; 4- PLA + HBR; 5- SAN + HBR; 6- SAN + PLA + HBR; and 7- PLA. Two fresh composite cylinders were constructed on each plate with NF or MH composites and tested after 24 h or 1 year of water-storage, using the MSBS testing. Data were analyzed by three-way ANOVA and Tukey test (α = 0.05). RESULTS: NF yielded better outcomes than MH at 24 h, which was not observed at 1 year. HBR showed the highest MSBS results, while untreated and PLA groups yielded the lowest one. MSBS reduced for all groups after 1 year. CONCLUSIONS: Only HBR can obtain good MSBS results, while PLA alone was not beneficial. After 1 year, a reduction in repair MSBS was observed and the type of composite did not influence the results. CLINICAL RELEVANCE: The repair technique can be simplified with the use of only an adhesive and macromechanical retentions in the old composite, regardless the type of fresh composite.

Full-mouth adhesive rehabilitation of a severe case of erosion treated with v-shaped veneers.

OBJECTIVE: To demonstrate a minimally invasive approach of a full-mouth rehabilitation of a severe case of erosion treated with v-shaped veneers, tabletops, overlays, veneerlays, laminate veneers, and a full contour veneer. CLINICAL CONSIDERATIONS: The present case report successfully rehabilitated a full-mouth case of severely eroded teeth with minimal healthy structure removal, maintaining viability of all teeth that were vital before the treatment started, and promoting long-lasting esthetic and functional results after 3 years of use. CONCLUSIONS: A deep knowledge of etiology, etiopathogenesis, and classifications of dental erosion will guide the clinician in the right direction for solving this issue correctly, according to modern prosthetic and conservative principles. CLINICAL SIGNIFICANCE: Dental erosion represents today a relatively widespread phenomenon among the global population and a significant challenge in each of its clinical stages for the clinicians who must treat it. In advanced stages, a careful evaluation phase of the case, a great patient motivation and a wise use of materials and clinical protocols are the success key of the case. Moreover, an advanced knowledge of adhesive dentistry is strictly required to successfully manage a severe erosion case with a modern and minimally invasive approach.

Microcomputed tomography evaluation of cement film thickness of veneers and crowns made with conventional and 3D printed provisional materials.

OBJECTIVE: To evaluate, through microcomputed tomography (µCT), the cement film thickness of veneers and crowns made with different provisional materials. MATERIAL AND METHODS: A veneer and a crown preparation were performed on a central incisor and a second molar of a dental model, respectively, scanned with an intraoral scanner, and the .stl files were exported to an LCD-based SLA three-dimensional (3D)-Printer. Twenty-four preparations were 3D-printed for each veneer and crown and divided into four groups (n = 6/group): (a) Acrylic resin (Acrílico Marche); (b) Bisacrylic resin (Protemp 4); (c) PMMA computer-aided design and computer-aided manufacturing (CAD-CAM) (Vipiblock); and (d) 3D-printed resin for provisional restorations (Raydent C&B for temporary crown and bridge). Veneers and crowns restorations were performed and cemented with a flowable composite. Each specimen was scanned with a µCT apparatus, files were imported for data analysis, and cement film thickness was quantitatively measured. Data were analyzed by 2-way ANOVA and Tukey post-hoc tests (α = .05). RESULTS: Crowns presented a thicker cementation film than veneers (P < .05).The bisacrylic resin showed the smallest veneer film thickness, similar to the acrylic resin (P = .151), which was not significantly different than the PMMA CAD/CAM material (P = .153). The 3D printed provisional material showed the thicker film, different than all other materials (P < .05). The bisacrylic resin showed a cement film thickness with a high number of voids in its surface. For crowns cementation, the 3D printed provisional material showed the thicker cementation film, different than all other materials (P < .05). CONCLUSIONS: Different provisional materials present different film thicknesses. The 3D printed provisional material showed the highest veneer and crown film thicknesses. Veneers film thicknesses were smaller than crowns for all provisional materials. CLINICAL SIGNIFICANCE: The 3D printed provisional material studied can be satisfactorily used, presenting appropriate adaptation with the tooth preparation, however, it shows the highest cement film thickness for both veneers and crowns cementations when compared with other provisional materials. A better internal fit, or smaller cement film thickness is obtained by CAD/CAM materials, acrylic and bisacrylic resins. Veneer cementation showed a smaller cement film thickness compared with crown cementation for all provisional materials.

Analysis of the color matching of universal resin composites in anterior restorations.

OBJECTIVE: To evaluate color matching of universal composite restorations performed in anterior teeth using two evaluation methods. MATERIALS AND METHODS: Sixty class III preparations were made on denture central incisors with different shades (A1-A3) and restored with multishade (Tetric Evoceram, Filtek Universal, and TPH Spectra Universal) and single-shade (Omnichroma) universal composites (n = 5). For photographic analysis, a digital photograph of each specimen was taken under standardized set-up. Color measurements were taken in the center of the restoration, and in the tooth surface 1.0 mm adjacent from the tooth/restoration margin. CIELab coordinates were recorded and color difference analysis (ΔE) was made using the CIEDE-2000 formula. For visual analysis, calibrated observers performed visual scoring of color matching and differences were graded as 0:excellent match; 1:very good match; 2:not so good match; 3:obvious mismatch; 4:huge mismatch. All data were statistically analyzed using a linear mixed model analysis with a confidence interval of 95%. RESULTS: For photographic analysis, Omnichroma showed the highest ΔE compared to the other composites for all shades (P < .05), without difference among experimental groups regarding tooth shade. For visual analysis, Omnichroma showed the highest scores (P < .05) for all teeth shades, without differences between the other groups. Furthermore, there were no differences between visual scores for different shades of a same resin composite group. CONCLUSIONS: Multishade universal composites presented higher color matching than the single shade universal composite. There were no differences of color matching for different tooth shades for all composites. CLINICAL SIGNIFICANCE: Universal composites with increased color matching may be helpful to simplify anterior restorations, minimizing clinical errors.

The injectable resin composite restorative technique: A case report.

OBJECTIVE: To describe the use of the injectable resin composite restorative technique with a flowable resin material, in a clinical case with esthetic problems associated with irregular tooth anatomies, allied with a finishing, and polishing protocol due to staining after 1 year of use. CLINICAL CONSIDERATIONS: The presented case report helped to achieve an immediate highly esthetic restoration with appropriate width proportions based on a previous wax-up. After 1 year of use, restorations presented staining; therefore, finishing and polishing procedures were required to re-achieve acceptable esthetic results and thus increase restoration's survival. CONCLUSIONS: The use of the presented technique allowed to obtain a simple and predictable workflow; however, care must be taken on the follow up of the restorations due to intrinsic characteristics of the flowable resin material. CLINICAL SIGNIFICANCE: The use of the presented injectable technique helped on obtaining a precise anatomy replicating a diagnostic wax-up, thus improving marginal precision and achieving a highly esthetic and functional immediate outcome, with an easy workflow when appropriately planned and executed. However, it also presented low color stability after 1 year of use only, thus, requiring attention from clinicians in regard to its maintenance over time.

Heating and preheating of dental restorative materials-a systematic review.

OBJECTIVES: To perform a review on the influence of preheating and/or heating of resinous and ionomeric materials on their physical and mechanical properties and to discuss the benefits and methods of preheating/heating that have been used. MATERIAL AND METHODS: A search was performed in the Pubmed, Scopus, Scielo, and gray literature databases. In vitro studies published from 1980 until now were searched using the descriptors "composite resins OR glass ionomer cements OR resin cements OR adhesives AND heating OR preheating." Data extraction and quality of work evaluation were performed by two independent evaluators. RESULTS: At the end of reading the search titles and abstracts, 74 articles were selected. Preheating of composite resins reduces viscosity, facilitates adaptation to cavity preparation walls, increases the degree of conversion, and decreases the polymerization shrinkage. Preheating of resin cements improves strength, adhesion, and degree of conversion. Dental adhesives showed good results such as higher bond strength to dentin. However, unlike resinous materials, ionomeric materials have an increase in viscosity upon heating. CONCLUSIONS: Preheating improves the mechanical and physical properties. However, there is a lack of clinical studies to confirm the advantages of preheating technique. CLINICAL RELEVANCE: Preheating of dental restorative materials is a simple, safe, and successful technique. In order to achieve good results, agility and training are necessary so the material would not lose heat until the restorative procedure. Also, care is necessary to avoid bubbles and formation of gaps, which compromises the best restoration performance.